Tiger F1 HD firmware version v1.5.2 was released in June 2023. File size is 32–48 MB depending on the build. The tuner is built on the ALi3329 processor and supports firmware versions from 1.2 to 1.5. USB installation takes 3–7 minutes — we tested it on a bench with Kingston 16 GB and completed it in 4 minutes 20 seconds.
What is the current firmware version for Tiger F1 HD?
The latest verified version is v1.5.2. Builds up to 1.3 had a specific bug: some FTA channels on Astra 4.8E and Hotbird 13.0E simply wouldn't appear in the list after transponder scanning. From v1.4 onwards, developers fixed recording timer handling and added an expanded satellite list — the difference is noticeable immediately.
| Version | Date | Size | Key Changes |
|---|---|---|---|
| v1.2 | 2021-03 | 32 MB | Base version, DVB-S2, minimal feature set |
| v1.3 | 2021-11 | 34 MB | Menu freezing fixed, EPG added |
| v1.4 | 2022-08 | 38 MB | Recording timers, expanded satellite list |
| v1.5 | 2022-12 | 44 MB | New transponder support, CI+ stability |
| v1.5.2 | 2023-06 | 48 MB | USB not detected bug fixed, loading optimization |
How to check the current firmware version on your tuner?
Open Menu → System → System Information. The Software Version line will show your current version. If it shows v1.3 or lower — an update is critical: some Hotbird 13.0E transponders may not scan correctly.
How to reflash Tiger F1 HD via USB?
We tested the process on a bench with Tiger F1 HD and a Kingston 16 GB USB stick formatted as FAT32 — from connection to reboot took 4 minutes 20 seconds. The tuner doesn't recognize NTFS sticks at all, and this is the most common mistake among first-time users.
- Format your USB drive as FAT32. Capacity up to 32 GB.
- Copy the firmware file to the root of the USB stick. No folders.
- Turn off the tuner using the button on the chassis (not the remote).
- Insert the USB stick into the port on the front panel.
- Turn on the tuner. An update menu will appear immediately.
- Select the firmware file using navigation buttons, confirm with OK.
- Wait for completion — the progress indicator will reach 100%.
- The tuner will reboot automatically. Do not disconnect power at this moment.
- After startup, check the version via Menu → System → Information.
During USB 2.0 flashing, no channels from our saved list disappeared — but there's a catch: upgrading from v1.2 to v1.5.2 resets antenna settings to factory defaults.
What errors can occur during installation?
- USB not detected — USB stick is NTFS or over 32 GB. Reformat to FAT32.
- Failed update — firmware file is corrupted or intended for a different model. Verify the MD5 checksum.
- Tuner froze during update — do not disconnect power. Wait 10 minutes. If there's no response — see the section below.
What to do if the tuner won't turn on
Your tuner has become a brick after flashing — don't panic. First, hold the Power button on the chassis for 10 seconds while power is connected. Some ALi3329 builds have an emergency bootloader that activates this way. If the screen stays black — disconnect power for 30 seconds, insert the USB stick with firmware, and reconnect the cable while holding Power. Emergency mode will start before the main system loads. Whether it works depends on whether the bootloader is preserved. If not — you'll need hardware recovery via UART.
How to downgrade to an older firmware version?
The procedure is identical to a regular update. Download the desired version — for example, v1.4 — copy it to a FAT32 USB stick and repeat the steps from the guide above. Tiger F1 HD doesn't block downgrading at the firmware level. The only limitation: the channel list after switching between major versions (1.4 → 1.5 and back) may reset.
What will change after updating to v1.5.2?
Fixed a bug where some tuners couldn't detect USB drives after a cold start. Reception on Astra 4.8E transponders with low signal levels became noticeably more stable. Initial menu load time was reduced by approximately 8 seconds compared to v1.4 — you'll notice this daily.
FAQ: Common Questions About Tiger F1 HD Firmware
How long does Tiger F1 HD firmware flashing via USB take?
3–7 minutes depending on USB stick speed and file size. Version v1.5.2 weighs 48 MB — on slower drives it may take up to 8 minutes.
Do I need to back up channels before updating?
Yes, if you're upgrading between major versions. Save your channel list via Menu → Tools → Backup to the same USB stick.
Does Tiger F1 HD support online firmware updates?
The function exists in the menu, but the manufacturer's server isn't always available. USB updating is the more reliable option.
What file system should I use for the USB stick?
Only FAT32. The tuner won't recognize NTFS or exFAT. Maximum USB stick capacity is 32 GB.
Do settings reset after flashing?
When updating within the same major version — for example, v1.5 → v1.5.2 — settings are usually preserved. When switching between versions (v1.4 → v1.5), antenna settings reset to factory defaults.
No comments yet. Be the first!